Technical diving has been a buzzword for several years now, but what is technical diving exactly? Here we’ll explain where recreational diving ends and technical diving starts.

What is technical diving? Ask most newly qualified open-water divers and they may struggle to explain exactly what that term means. Even recreational-diving instructor candidates often don’t necessarily have a one-sentence answer.

For years, my go-to explanation was: ‘Remember the limits you learned — not to exceed certain depths and times? Technical diving teaches you to go beyond those depths and times, but plan for it.’ Oversimplified? Perhaps. So, let’s look at other definitions.

What is technical diving?

The National Oceanic and Atmospheric Administration (NOAA) defines technical diving as “all diving methods that exceed the limits imposed on depth and/or immersion time for recreational scuba diving. Technical diving often involves the use of special gas mixtures…

Technical diving almost always requires one or more mandatory decompression “stops” upon ascent, during which the diver may change breathing gas mixtures at least once…”

Within these few lines, we learn some of the key components of technical diving, such as exceeding recreational depth and time limits, choosing breathing gases and making gas changes. This definition doesn’t touch upon the need for additional equipment, which is almost a foregone conclusion.

Equipment

As technical diving often involves diving deeper and staying longer than recreational divers normally would, tech divers require more gas. And, if divers take more than one breathing gas with them, it follows that they’ll need at least one additional cylinder, complete with rigging and regulators.

A single tank is usually not enough for two reasons. First, it doesn’t hold enough gas. Second, it does not offer enough redundancy if you have an equipment failure, such as a regulator or valve malfunction. Consequently, technical divers tend to use twinsets/doubles or sidemount tanks.

But technical divers don’t only take back-up tanks and regulators. Tech divers carry two masks, dive computers and/or depth-timing devices, SMBs and/or lift bags and any other lifesaving equipment.

Dive planning

Another crucial difference between recreational and technical diving is the amount of planning involved in either. Technical divers learn to calculate how much gas they are likely to use on their dive. This forms the basis of their dive planning. Add to that suitability of gases, equipment requirements, logistics and so much more, and it becomes clear why technical planning usually takes a bit longer.

Divers often use desktop software to produce individual dive plans suitable for each dive site’s topography and expected conditions. Plans include gas supplies, descent and ascent speeds, gas-switching depths, required amounts of gas for emergencies and more.

Specialist skills

Technical divers must possess specialist skills, including the ability to manage several different gases. They practice this task in certification courses, as well as learning emergency skills. Like recreational diving courses, tech courses contain a mix of skills applied to most dives, including propulsion techniques, gas switching, trim and buoyancy control and emergency skills, such as cylinder shutdowns, mask switching and more.

Being able to quickly and competently execute those skills can make the difference between life and death or prevent serious injury in a technical-diving scenario. This is especially true for overhead environments, including caves and wrecks. Both are unforgiving environments where you must have sharp dive skills.

Therefore, tech divers must keep their skills fresh and practice them regularly. Consequently, you may see someone taking a twinset and two or more stage tanks to 60 feet (20 m).

It’s a mindset

Becoming a technical diver is likely to change a diver’s approach to all their diving. TDI’s Advanced Nitrox course, for example, mentions a ‘performance mindset.’ This means that the diver is in control of each part of their dive. Practically, divers might conduct more thorough pre-dive checks, spend some time writing a dive plan on a slate, carry specialist computers and generally be in their own world before a dive.

While some of this becomes automatic after a while, it takes time to get there, but the reward is entry to places few divers ever go.

Have something to add to this post? Share it in the comments.
New stuff
Back-Roll Entry

Training Fundamentals: Perfecting Your Scuba Back-Roll Entry

The scuba back-roll entry should be as easy as falling off a boat, but what’s the best way to prepare and enter the water using a back-roll entry?
by Marcus Knight
Pygmy Seahorse

Marine Species: Pygmy Seahorse

One of the hardest critters to spot, the pygmy seahorse is a fascinating creature. Let’s look at a few attributes of this tiny yet spectacular animal.
by Hélène Reynaud
Yasawa Islands

Scuba Diving in Fiji’s Yasawa Islands

Fiji has a reputation as the friendliest country in the world and offers some fantastic diving. The Yasawa Islands are some of the best of the best.
by Guest Author
Lonely Whale

Conservation Spotlight: Lonely Whale

In this series of articles, we’ll profile conservation organizations focused on ocean protection. Today we’re chatting with Emy Kane from Lonely Whale.
by Hélène Reynaud